Antik MG2 Breeze Roller Skate with PowerDyne's 10-degree aluminum Reactor Neo plate. The Neo is strong, stable, and built to maximize the power transfer of your stride. (LAST CHANCE TO PURCHASE THIS SKATE - DISCONTINUED)
Antik MG2 Boot Features:
- High cut leather uppers for added ankle support and secure fit
- Redesigned fully enclosed, contoured padded leather tongue
- All new ‘Ergo-Form’ last for a more anatomical fit, and to reduce toe pinch.
- All new open toe design for better fit and comfort
- Dri-lex interior lining
- Standard fiber counters
- All new lace loops at the back of heel for added fit and security
- Redesigned achilles area
- Integrated shock absorbing heel
- Contoured heel cup for secure fit and reduced lift
- Composite rubber outsole, stitched for durability
- Standard fabric insoles
- Available in whole and half sizes
- US size 3-13
- Heat-treated lightweight extruded aircraft aluminum plate
- 10 degree kingpin angle for enhanced STABILITY
- Click action lock nuts for the kingpins
- Steel rod reinforced pivot arms and durable done piece Delrin pivot cups
- Solid 7075 aluminum kingpins
- rounded front of truck for less scratching on the floor
Antik Heat Molding Instructions
Depending on how you want your boots to fit, there are a few options for heat molding the counters and toe box.
After molding, the metal components of skate boots may be very HOT! Watch out for buckles, eyelets, and aglets! After heating and lacing up the boot, try not to move around too much. Ideally you want to be in a skating stance so that your foot is as close to the shape that it would be while skating. Moving around in the boot will not allow the boot to cool in a uniform manner. Finally, after initial cooling, allow the boot to stand for several hours (up to a day) before any rigorous skating!
Option 1 (for specific "trouble spots"): Heat Gun or Hair Dryer
This option is for individual problem areas (toes, arch, outer foot), and lets you mold one section at a time. Keep the gun/dryer approximately 6-8 inches away from the boot, moving in a small circular pattern so as not to over heat one spot. This should take about 3 minutes with a heat gun and 6-7 with a hair dryer. Once the material is pliable, use your hands to massage & push out the problem spot, and hold until cool (blunt end of screwdriver can be used to push out particularly tight spots). This process can be repeated as many times as needed.
Option 2 (for general fit): Skate Bake or Kitchen Oven
This option allows you to mold all three spots at once. Mold only one boot at a time! First, pre-heat oven to ~175 degrees; do NOT exceed 200 degrees! Remove insole, laces, toe stop, wheels, and bearings (cushions can be left on). Place boot/skate in oven on rack or cookie sheet for 3 minutes. Remove boot (it will be HOT!). Insert insole, place foot in boot and lace up (wearing socks you wear while skating). Stand up in boots, in skating stance, and wait until cool. This process can be repeated as many times as needed.
AR1 and MG2: Antik suggest going down 2 whole sizes from your Riedell size but it has been found most people are half a size down from their Riedell size. The chart below has been made with the ‘half a size lower than Riedell’ in mind. If you prefer a bit of extra room, add a little extra to the measurement. My feet measure 25.4 cm and I fit the size 7.5 and an 8 in Riedell boots.
To determine your length - In a standing position and on a flat surface place your heel against a wall and take a ruler or tape measure and lay it next to your foot. Measure from your longest toe to your heel. It is best to do this measurement with both feet in case one foot may be slightly longer than the other.
All Antik boots are made on a D/B last which means a D width ball and a B width heel.
Foot length (mm)
Interior Length (cm)